FANUC数控系统 0系统参数大全   

1、发那科数控系统SETTING 参数 

参数号       符号          意义             0-T         0-M 

0000       PWE         参数写入            O           O 

0000       TVON       代码竖向校验        O           O 

0000       ISO          EIA/ISO代码        O          O 

0000       INCH        MDI方式公/英制    O          O 

0000       I/O          RS-232C口         O          O 

0000       SEQ         自动加顺序号         O          O   

2、FANUC数控系统RS232C口参数 

2/0       STP2        通道0停止位       O       O 

552                   通道0波特率       O       O 

12/0     STP2        通道1停止位       O       O 

553                   通道1波特率       O       O 

50/0     STP2       通道2停止位       O       O 

250                  通道2波特率       O       O 

51/0       STP2      通道3停止位       O       O 

251                  通道3 波特率       O       O 

55/3    RS42     Remote Buffer 口RS232/422       O       O 

390/7     NODC3       缓冲区满       O       O  

3、FANUC数控系统伺服控制轴参数 

1/0             SCW       公/英制丝杠       O       O 

3/0.1.2.4       ZM         回零方向       O       O 

8/2.3.4         ADW        轴名称             O 

30/0.4         ADW        轴名称       O       

32/2.3         LIN         3,4轴,回转轴/直线轴       O       

388/1          ROAX      回转轴循环功能       O       

388/2          RODRC    绝对指令近距离回转       O       

388/3          ROCNT     相对指令规算       O       

788             回转轴每转回转角度       O       

11/2       ADLN       第4轴,回转轴/直线轴             O 

398/1       ROAX       回转轴循环功能             O 

398/2       RODRC       绝对指令近距离回转             O 

398/3       ROCNT       相对指令规算             O 

788             回转轴每转回转角度       O       

860       回转轴每转回转角度             O                         

500-503  INPX,Y,Z,4       到位宽度       O       O 

504-507   SERRX,Y,Z,   运动时误差极限       O       O 

508-511       GRDSX.Y,Z,4       栅格偏移量       O       O 

512-515       LPGIN       位置伺服增益       O       O 

517         LPGIN     位置伺服增益(各轴增益)       O       O 

518-521       RPDFX,Y,X,4       G00速度       O       O 

522-525       LINTX,Y,Z,4       直线加/减速时间常数       O       O 

526          THRDT         G92时间常数       O       

528       THDFL       G92X轴的最低速度       O       

527       FEDMX       F的极限值       O       O 

529       FEEDT       F的时间常数       O       O 

530       FEDFL       指数函数加减速时间常数       O       O 

533       RPDFL       手动快速移动倍率的最低值       O       O 

534       ZRNFL       回零点的低速       O       O 

535-538       BKLX,Y,Z,4     反向间隙       O       O 

593-596       STPEX,Y,Z,4    伺服轴停止时的位置误差极限       O       O 

393/5             快速倍率为零时机床移动       O       O  

4、发那科数控系统坐标系参数 

10/7       APRS       回零点后自动设定工件坐标系       O       O 

2/1       PPD       自动设坐标系相对坐标值清零       O       

24/6       CLCL       手动回零后清除局部坐标系             O 

28/5       EX10D       坐标系外部偏移时刀偏量的值（×10）             O 

708-711             自动设定工件坐标系的坐标值             O 

735-738             第二参考点       O       O 

780-783             第三参考点       O       O 

784-787             第四参考点       O       O   

5、FANUC数控系统行程限位 

8/6       OTZN       Z轴行程限位检查否             O 

15/4       LM2       第二行程限位             O 

24/4       INOUT       第三行程限位             O 

57/5       HOT3       硬超程-LMX--+LMZ有效             O 

65/3       PSOT       回零点前是否检查行程限位       O       O 

700-703             各轴正向行程       O       O

704-707             各轴反向行程       O       O 

15/2       COTZ       硬超程-LMX--+LMZ有效       O       

20/4       LM2       第二行程限位       O       

24/4       INOUT       第三行程限位       O      

743-746             第二行程正向限位             O 

747-750             第二行程反向限位             O 

804-806             第三行程正向限位             O 

807-809             第三行程反向限位             O 

770-773             第二行程正向限位       O       

774-777             第二行程反向限位       O       

747-750             第三行程正向限位       O       

751-754             第三行程反向限位       O       

760-763             第四行程正向限位       O      

764-767             第四行程反向限位       O    

6、法兰克数控系统进给与伺服电机参数 

1/6       RDRN     空运行时,快速移动指令是否有效       O       O 

8/5       ROVE     快速倍率信号ROV2(G117/7)有效             O 

49/6       NPRV    不用位置编码器实现主轴每转进给       O       O 

20/5       NCIPS   是否进行到位检查       O       O 

4—7             参考计数器容量       O       O 

4—7             检测倍比       O       O 

21/0.1.2.3     APC     绝对位置编码器       O       O 

35/7       ACMR    任意CMR       O       O 

37/0.1.2.3 SPTP    用分离型编码器       O       O 

100-103             指令倍比CMR       O       O 

7、FANUC数控系统DI/DO参数 

8/7       EILK       Z轴/各轴互锁       O       O 

9/0.1.2.3       TFIN       FIN信号时间       O       O 

9/4.5.6.7       TMF       M,S,T读信号时间       O       O 

12/1       ZILK       Z轴/所有轴互锁             O 

31/5       ADDCF       GR1,GR2,DRN 地址       O       

252             复位信号扩展时间       O       O  

8、发那科数控系统显示和编辑 

1/1       PROD       相对坐标显示是否包括刀补量       O       O 

2/1       PPD       自动设坐标系相对坐标清零       O       O 

15/1       NWCH       刀具磨损补偿显示W       O       O 

18/5       PROAD       绝对坐标系显示是否包括刀补量             O 

23/3       CHI       汉字显示       O       O 

28/2       DACTF       显示实际速度       O       O 

29/0.1       DSP       第3,4轴位置显示       O      

 35/3       NDSP       第4轴位置显示             O 

38/3       FLKY       用全键盘       O       O 

48/7       SFFDSP       显示软按键       O       O 

60/0       DADRDP       诊断画面上显示地址字       O       O 

60/2       LDDSPG       显示梯形图       O       O 

60/5             显示操作监控画面       O       O 

64/0       SETREL       自动设坐标系时相对坐标清零       O       O 

77/2             伺服波形显示       O       O 

389/0       SRVSET       显示伺服设定画面       O       O 

389/1       WKNMDI       显示主轴调整画面       O       O

9、FANUC数控系统编程参数 

10/4       PRG9       O9000-O9999号程序保护       O       O